Hydraulics and pneumatics - Study guides, Class notes & Summaries

MSSC MAINTENANCE PNEUMATICS Questions WITH VERIFIED 100% CORRECT ANSWERS Which are considered a fluid system, pneumatics or hydraulics? - ANSWER Both are considered fluid systems What are the two types of conductors used in a pneumatic system? - ANSWER Supply line and actuator line The S.I. unit for pressure is? - ANSWER kPa What is the maximum pressure that the gauge shown can measure? - ANSWER 7000 kPa What value is shown on the gauge? - ANSWER 56 psi To convert gauge pres...

UNDERSTANDING HYDRAULICS PNEUMATICS IN CIVIL ENGINEERING EXAM...

pilot line correct answer: A dashed line in a pneumatic schematic diagram represents a(n)... A positive displacement air compressor... correct answer: produces a new volume of air for every stroke An accumulator is a hydraulic component that... correct answer: stores fluid under pressure At a given flow rate, a cylinder retracts faster than it extends because... correct answer: the rod takes up space Before disconnecting oil lines, correct answer: lockout/tagout equipment Com...

Incident Safety Officer Exam Questions With 100% Correct Answers 2024/2025 Individual turbine blades can be __ to __ feet long creating a rotational diameter and danger zone of more than ___ feet 60 to 130/300 a ___ is defined in writing and can take on many forms:SOPS, SOGS, departmental directives, temporary memorandums formal process Procedures Strict directives that must be followed with little or no flexibility An ___ is a process or operation that is part of a department...

An automobile traces 10 miles in 15 minutes - 40 A 12 tooth sprocket and a 60 tooth sprocket are connected by a chain. - Counterclockwise If the ramp is inclined 30 degrees and the friction of the ramp is 0.25 - 284 A torque of 15 feet is the result when ______ acts on a 6 in wrench - 30 Formula for pressure - force/area 12 tooth gear is meshed with a 60 tooth gear - 25:1 Raise the arm of a robot, last of 6 gears must rotate clockwise - Counterclockwise A torque of 30 ft*lbs is the result...

Jig - A device that holds and locates a piece of work and guides the tools that operate upon it. Example: table, anything that is used to guide material. Fixture - A device designed and built for holding a particular piece of work for machining operations without the ability to guide tools Postprocessor - A post-processor is in essence software and or a sequence of instructions to deal with a nuetral format generated by a CAM system and translates that nuetral language to one that makes yo...

Torches are designed to avoid mixing oxygen and acetylene by using __________. Reverse-flow check valves at torch inlets or regulator outlets To prevent leakage around the valve during use, __________ An oxygen cylinder valve should be opened all the way An explosion can occur if __________ comes in contact with oil. High pressure oxygen A green welding hose normally indicates that this hose carries __________. Oxygen A __________ is a non-destructive test that us...

Torches are designed to avoid mixing oxygen and acetylene by using __________. - Answer Reverse-flow check valves at torch inlets or regulator outlets To prevent leakage around the valve during use, __________ - Answer An oxygen cylinder valve should be opened all the way An explosion can occur if __________ comes in contact with oil. - Answer High pressure oxygen A green welding hose normally indicates that this hose carries __________. - Answer Oxygen A __________ is a non-destruct...

What kind of process do engineers use to design and create solutions to problems? - Answer Engineering design process Which of the following are examples of scientific knowledge sometimes needed in engineering? - Answer Statics, Ohm's law, and thermodynamics Engineers in the (Blank) discipline must understand concepts such as pneumatics, hydraulics, power transmission, gear ratios, and efficiency - Answer Mechanical Engineering (Blank) is the design and coordination of all aspect...

Torches are designed to avoid mixing oxygen and acetylene by using __________. Reverse-flow check valves at torch inlets or regulator outlets To prevent leakage around the valve during use, __________ An oxygen cylinder valve should be opened all the way An explosion can occur if __________ comes in contact with oil. High pressure oxygen A green welding hose normally indicates that this hose carries __________. Oxygen A __________ is a non-destructive test that us...