35 psi - Study guides, Class notes & Summaries

Ground reservoirs are man-made impoundments that have the same characteristics of a pond or small lake. They are most commonly found at: A. Commercial properties B. Industrial properties C. Municipal water treatment facilities D. All of the above correct answers D Pump piping on fire apparatus must be able to withstand hydrostatic test pressures of: A. 100 psi B. 250 psi C. 500 psi D. 750 psi correct answers C NFPA 1901 brake test requires that new fire apparatus be brought to ...

TFS Midterm Prep Questions and Answers 100% Pass The MSA G1 SCBA is a ________________ open-circuit, positive pressure SCBA Air cylinders and valve assembly should be tested Every 3-5 years MSA G1 SCBA COMPONENTS - Air cylinders and valve assembly - G1 Pressure reducer with low pressure warning device - G1 regulator - G1 HEADS UP DISPLAY - G1 face piece - G1 control module - G1 speaker module - G1 power module - G1 battery module - G1 Harness and carrier assembly G1 Press...

FDNY S-92 Questions and Answers Rated A+ The following are types of what? LPG, CNG, piped natural gas or solid fuel (coke). Portable fueled salamanders/space heaters National Institute for Occupational Safety and Health (NIOSH) Recommended Exposure Limit (REL) for carbon monoxide 35 parts per million (ppm) over an 8 hour period What is the third leading cause of fires in buildings under construction ? temporary heating What is direct heat flow through matter? CONDUCTION What is the transport...

TFS MIDTERM PREP EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ The MSA G1 SCBA is a ________________ Correct Answer: open-circuit, positive pressure SCBA Air cylinders and valve assembly should be tested Correct Answer: Every 3-5 years MSA G1 SCBA COMPONENTS Correct Answer: - Air cylinders and valve assembly - G1 Pressure reducer with low pressure warning device - G1 regulator - G1 HEADS UP DISPLAY - G1 face piece - G1 control module - G1 speaker module - G...

net floor are - occupant load complaint with no immediate action required - assigned routinely to inspection staff are company officer extinguisher with no residue - clean agent NFPA resident occupancy - apartments UN class 5 - oxidizer open lake or canal - reservoir extinguisher common to b or c - potassium bicarb, purple k panic bar settings - hush bar 15 lb Open door 30 lb testing safety products - ASTM fire drill for healthcare facilitie...

What is the minimum size of a water meter and service piping in inches for a water supply system of 34 fixture units with a maximum developed length of 200 feet. The water pressure of the system is 35 psi. - Answer- 1 Table AP201.1 What is the minimum sized trap that can be used for the drainage system of a bathtub (with or without shower head and/or whirlpool attachments)? - Answer- 1.5 Table P3201.7 A water heater pan drain must extend full-size and terminate over a suitably locat...

CPO Practice Test Questions and Answers Already Passed Which type of filter requires the least amount of water to clean? (A) Diatomaceous (B) Rapid rate sand (C) High rate sand (D) Cartridge (D) Cartridge Cyanuric acid (stabilizer) protects free chlorine (FC) against the effects of: (A) Pathogens like Crypto, Giardia, and Shigella (B) High Total dissolved solids (C) Ultraviolet rays from the sun (D) High PH (C) Ultraviolet rays from the sun An erosion chemical feeder is what ty...

Gas Fitter 2 Practice Test - Questions and Answers Installation of one 400,000 btu natural draft boiler in a tight enclosure would require an air supply opening of? A. 114 sq in B. 50 sq in C. 58 sq in D 112 sq in With the installation of a 75,000 btu atmospheric hot water tank in a tight house, how much free air is required when using a round duct? A. 11" B. 4" C. 7" D. 3" A portable infrared heater that cannot be interlocked shall be connected to a: A. CO2 monitor alarm B. CO monitor ala...

FCTC WRITTEN EXAMINATION >> COMPLETE SET ACTUAL QUESTIONS AND CORRECT DETAILED ANSWERS What does "fre, 123" mean? - ANSWER : Fulcrum is in the middle for Class 1 LeversResistance (output) in middle for Class 2Effort (input) in the middle for Class 3 Formula for Determining the head pressure difference between an intake and output - ANSWER : 1 vertical foot = 0.433 psi 1 psi = 2.31 vertical feet Overall Test Overview: - ANSWER : 1) 30-minute period to read 2 essays- 2-h...

ACI Concrete Strength Exam Study Guide - Questions and Answers These procedures for capping enable concrete cylinders and cores to meet the standard practice's requirements for _____ and _____. Planeness; perpendicularity Equipment needed for the capping process includes capping ____ ____ devices and _____ pots. Plates; alignment; melting Plates for neat cement and high-strength gypsum plaster caps should be made of ____, _____, or _____. Metal; glass; granite Sulfur mortar cap plates should ...