Fanuc 3 - Study guides, Class notes & Summaries

FANUC HANDLING PRO LATEST UPDATE Enabling the iPendant gives motion solely to whom? A. The PLC B. The Controller C. The Operator - CORRECT ANSWER C Assuming standard setup, if you jog the robot in World -Y, which direction will the TCP move? A. Straight out front B. Up C. To the robots right D. To the robots left - CORRECT ANSWER C What key is depressed to switch between the different jog modes? A. POSN B. MENU C. FCTN D. COORD - CORRECT ANSWER D What two buttons display...

FANUC STUDY GUIDE TEST. Enabling the iPendant gives motion solely to whom? A. The PLC B. The Controller C. The Operator - CORRECT ANSWER C Assuming standard setup, if you jog the robot in World -Y, which direction will the TCP move? A. Straight out front B. Up C. To the robots right D. To the robots left - CORRECT ANSWER C What key is depressed to switch between the different jog modes? A. POSN B. MENU C. FCTN D. COORD - CORRECT ANSWER D What two buttons display the ...

FANUC HANDLING PRO LATEST UPDATE Enabling the iPendant gives motion solely to whom? A. The PLC B. The Controller C. The Operator - CORRECT ANSWER C Assuming standard setup, if you jog the robot in World -Y, which direction will the TCP move? A. Straight out front B. Up C. To the robots right D. To the robots left - CORRECT ANSWER C What key is depressed to switch between the different jog modes? A. POSN B. MENU C. FCTN D. COORD - CORRECT ANSWER D What two buttons display...

FANUC NOCTI Training Part 3 Study Guide Test. Axis Limits Define What - CORRECT ANSWER Upper and lower Motion Degree limitations To Set AXIS limits - CORRECT ANSWER Menu>System>Axis Limits What 3 things does Payload tell the robot - CORRECT ANSWER Mass Center of Mass (COG) Robots Motion (inertia) 2 ways to setup Payload - CORRECT ANSWER Manual Entry Automatic Estimation Where is Payload located - CORRECT ANSWER Menu>System>Motion List the 6 types of mastering - C...

Unit 2-3 FANUC Review

FANUC Cert Test Questions with Correct Answers List the Major Axis - Correct Answer J1, J2, J3 List the Minor Axis - Correct Answer J4, J5, J6 Identify the Components of the SOP - Correct Answer 1. Fault Reset 2. Cycle Start 3. Fault LED 4. Power LED 5. E-STOP 6. Mode Switch 7. Hour Meter Which mode limits all cartesian speed to less than 250 mm/sec and joint speed to less than 10%? - Correct Answer T1 Mode Enabling the iPendant gives motion control solely to whom? - Correct A...

Fanuc Section 3 – Handling Pro Study Guide Test. click on cycle start within the icon bar - CORRECT ANSWER To run and view a program from beginning to end utilizing the EOAT pick and place a part A) right click on the program within the cell browser and select run program B) from the test-run menu, select run panel C) right click on the robot and select run program D) click on cycle start within the icon bar allows you to drag the EOAT - CORRECT ANSWER What is the teach tool? A) a...

Fanuc Exam Questions with All Correct Answers speed and termination types are pasted in the proper instructions to maintain the original speed and termination of each path segment - Answer-F3 -- RM-POS-ID will add lines exactly as they were copied and renumbers the copied positions with the next available position number - Answer-F4 - POSITION will add the lines exactly as they were copied, but leaves the position numbers blank - Answer-F2 - LOGIC will add lines exactly as they were c...

Fanuc Robots Exam Questions with Complete Solutions 3 motion instructions? - Answer-Joint Linear Circular 2 position types? - Answer-Position Command Position Register 3 speed types? - Answer-% mm/sec in/min 2 termination types? - Answer-Fine Continuous Button for program screen? - Answer-Select How many major axis? - Answer-Three major= 1, 2, 3 How many minor axis? - Answer-Three minor= 4, 5, 6 T or F: A "C" move has 3 points? - Answer-F T or F: Position com...