ASE A1 (Engine Repair) Practice Test – Cumulative (100% Correct answers)
an engine miss is being diagnosed using a cylinder leakage test.
Technician A says that any cylinder with over 20% leakage has excessive leakage. Tech B says that air
leaking from the tailpipe indicates a cracked cylinder.
A only,
B only,
A & B,
Neither . correct answers A only:
If cylinder leakage exceeds 20%, check for air escaping the tailpipe, the PCV valve opening in the rocker
arm cover, and the top of the throttle body or carburetor.
Air leaking from the tailpipe usually indicates an exhaust valve leak
during a compression test, a cylinder has 40% of the specified compression reading. When the tech
performs a wet test, the compression reading on this cylinder has 75% of the specified reading. The cause
of the low compression reading could be
worn piston rings,
a burned exhaust valve,
a bent intake valve,
a worn camshaft lobe, correct answers worn piston rings
if compression increases during a wet test, this indicates worn piston rings. Compression would not
increase if an exhaust valve is burned, intake valve is bent, or camshaft lobe is worn.
the customer complains that the engine cranks but does not start; the first thing to check should be
valve train operation,
battery voltage,
compression,
,engine vacuum, correct answers valve train operation:
if the engine cranks properly, the battery is not the problem. Compression would not be the FIRST test,
and because engine vacuum is low during a crank, a vacuum test would not be conclusive.
during a cylinder balance test on an engine with fuel injection, one cylinder provides very little rpm drop.
Tech A says the ignition system may be misfiring on that cylinder.
Tech B says the engine may have an intake manifold vacuum leak.
A only,
B only,
A & B,
Neither , correct answers Both A&B
Both a misfiring ignition system and an intake manifold leak could cause a cylinder to contribute too little
power
while discussing basic diagnostic procedures,
Tech A says the most complicated diagnostic tests should be performed first. Tech B says that you should
first question the customer to obtain as much info as possible about the problem
A,
B,
A & B,
Neither, correct answers B
Always attempt the more simple diagnosis first
with the engine idling, a vacuum gauge connected to the intake manifold fluctuates (from 15 to 20). These
fluctuations may be caused by
,late ignition timing,
intake manifold vacuum leaks,
a restricted exhaust system,
sticky valve stems and guides, correct answers sticky valve stems and guides
-late ignition timing would result in a low, steady reading
-intake manifold leaks would cause a very low, steady reading
-a restricted exhaust system would cause vacuum to slowly decrease after the engine was accelerated and
held steady
oil is leaking from the crankshaft rear main bearing seal on an engine. Tech A says the oil seal could be
faulty. Tech B says the PCV system may not be functioning.
A,
B,
A & B,
Neither, correct answers A&B
A high-pitched squealing noise is heard during hard acceleration. This may be the cause of:
intake manifold leak,
the choke stuck closed
fuel system leak
small leak in exhaust manifold correct answers small leak in exhaust manifold
-intake manifold leak causes a high-pitched whistle at idle and low speeds
-carb choke stuck closed will not cause a high-pitched whistle
-fuel system leak normally would not cause a noise
, a heavy thumping noise occurs with the engine idling, but the oil pressure is normal. this may be caused
by:
worn pistons and cylinders,
loose flywheel bolts,
worm main bearings,
loose camshaft bearings, correct answers loose flywheel bolts
-worn pistons and cylinders would cause a thumping noise during acceleration
-worn main bearings cause a thump when the engine is started
-loose camshaft bearings would cause a growling noise at all times
after a vehicle is parked overnight and then started in the morning, the engine has a lifter noise that
disappears after running for a short time. this may be caused by:
low oil pressure,
low oil level,
worn lifter bottom,
excessive lifter leak-down, correct answers excessive lifter leak-down
low oil pressure would result in a continuous noise
low oil level would result in a continuous noise
worn lifter bottom would result in a continuous noise
when using a compression tester, the readings on the cylinders are all even, but lower than spec. this
could indicate:
blown head gasket,
carbon buildup,
cracked head,
worn rings and cylinders, correct answers worn rings and cylinders
