100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
Previously searched by you
NACE CIP 1 CBT EXAM WITH QUESTIONS AND VERIFIED ANSWERS || GRADED A+ | LATEST VERSION | GUARANTEED PASS According to ASTM D 4417 Method B 2014 when taking measurements using a profile gauge, at each location you should make? - ANSWER-10 readings per l$20.49
Add to cart
NACE CIP 1 CBT EXAM WITH QUESTIONS AND VERIFIED ANSWERS || GRADED A+ | LATEST VERSION | GUARANTEED PASS According to ASTM D 4417 Method B 2014 when taking measurements using a profile gauge, at each location you should make? - ANSWER-10 readings per l
6 views 0 purchase
Course
NACE CIP 1 CBT
Institution
NACE CIP 1 CBT
NACE CIP 1 CBT EXAM WITH QUESTIONS AND
VERIFIED ANSWERS || GRADED A+ | LATEST
VERSION | GUARANTEED PASS
According to ASTM D 4417 Method B 2014 when taking measurements using a
profile gauge, at each location you should make? - ANSWER-10 readings per
location, recording the maximum value. D...
NACE CIP 1 CBT EXAM WITH QUESTIONS AND
VERIFIED ANSWERS || GRADED A+ | LATEST
VERSION | GUARANTEED PASS
According to ASTM D 4417 Method B 2014 when taking measurements using a
profile gauge, at each location you should make? - ANSWER-10 readings per
location, recording the maximum value. Determine mean (average) for all
maximum valises the reported profile.
What is an advantage of airless spray compared to conventional air spray? -
ANSWER-Faster production rate
You arrive to inspect a bride repainting project where containment (enclosure) has
already been erected but dehumidification is not being used. What Inspection
challenges do you expect specific to working inside the containment? - ANSWER-
Illumination and Control of temperature and humidity.
Improper atomization of the coating may cause which of the following? -
ANSWER-Uneven DFT, Dry Spray and Overspray.
High viscosity due to low temperature should be corrected by? - ANSWER-
Adding extra thinner.
SSPC Technology Guide No. 12 states coating inspection requires a minimum of
which of the following? - ANSWER-50-foot candles (538 lumens)
,One major advantage of conventional spray? - ANSWER-Applicator control.
When using a wet film thickness (WFT) comb/gauge, the measurement should be
taken? - ANSWER-Immediately after the coating is applied.
A well-written specification requires a surface profile depth defined as? -
ANSWER-A range of measurements.
The testing for water-soluble ferrous salts is? - ANSWER-Potassium Ferricyanide
Test
Solvent-borne inorganic zinc primer is being applied with airless spray to complex
bride with difficult access for the application. The contractor is having difficulty
with hight DFT resulting in mud cracking. What application method might be a
good alternative? - ANSWER-Conventional Spray
Common errors that can produce inaccurate readings when using Wet Film
Thickness (WFT) gauges include: - ANSWER-Using a damaged gauge and
dragging gauge though wet coating.
ISO ST 3 is described as: - ANSWER-Very Thorough hand or power tool cleaning
You are an Inspector on a project where SSPC SP3 is specified. What sort of tools
should you expect the Contractor to use to achieve the standard? - ANSWER-
Power Tools
The least effective method of surface cleaning is most likely: - ANSWER-Hand
Tool Cleaning
, Nace No. 4/SSPC SP 7 is a joint standard for: - ANSWER-Brush Off Blast
Cleaning
Surface profiles describes: - ANSWER-The level of surface roughness required
after abrasive blasting.
To be of value the Inspectors documentation must be: - ANSWER-Timely,
accurate and concise.
A NACE Coating Inspector is permitted to transport coating material when: -
ANSWER-The Inspector should never transport coating material.
Solvents are added to coating formulations to: - ANSWER-Dissolve binders and
form liquid coatings.
(Also known as 'fisheyes' or 'crawling') is the term for surface breaks in the film
that reveal the substrate. It is often a result of grease or oil contamination on the
substrate. - ANSWER-Cissing
You are reviewing the documentation for a tank waiting project and notice there is
a conflict between the project specification and the manufacture's product data
sheet on the required DFT of the primer. The owner is not reachable for
clarification. What should be done? - ANSWER-Follow the specification.
You know that you are sensitive to amines, but not polyamides. What document
would you review prior to arriving on the joist to know whether amines will be
used? - ANSWER-The contractor's contract.
The formation of small bowl-shaped depressions in the coating find cause by air
trapped in the coating is called? - ANSWER-Cratering
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller winnieelizabeth424. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $20.49. You're not tied to anything after your purchase.
