CWB Level II Exam Questions & Answers 100% Correct
8 views 0 purchase
Course
CWB Level II
Institution
CWB Level II
CWB Level II Exam Questions & Answers 100% Correct CWB Level II Exam Questions & Answers 100% Correct CWB Level II Exam Questions & Answers 100% Correct
What is the term used to describe the following condition of lost corrosion resistance?
"When certain stainless steels are heated between 5...
Note: Also known as "carbide precipitation" -- Chromium binds to carbides, and "sweats
out" at the grain boundaries
On a radiograph, undercut appears as a _________ line.
(A) light
(B) dark - ANSWER-(B) dark
What is the Canadian Standard for safety in welding? - ANSWER-CSA W117.2
What is the typical three-phase input voltage in most Canadian welding shops? -
ANSWER-600V
True or False: The cable from the workpiece back to the welding machine is called the
"ground lead". - ANSWER-False. The correct term is the "work lead".
What is the type of radiation that can damage living cells? - ANSWER-Ionizing
Name two examples of ionizing radiation. - ANSWER-X-rays and Gamma rays
What is the minimum suggested shade for a welding helmet when using 5/32 SMAW
electrode at 150 A? - ANSWER-Shade 10
What is the typical max. OCV of an AC welding machine? - ANSWER-80 V
In an isometric drawing, the lines (for width, length and depth) are inclined at an angle
of how many degrees? - ANSWER-30°
,What are the maximum number of views in an orthographic drawing? - ANSWER-6
What are the two general classes of picture drawings? - ANSWER-Perspective and
Isometric
Approx. how far could spatter travel when welding/cutting from 2.5m high? - ANSWER-
Possibly up to 6m
What is the toxic component contained in some copper alloys? - ANSWER-Beryllium
Which welding process will likely have the highest fume generation rate?
[SMAW / SAW / FCAW] - ANSWER-FCAW
What do the terms TLV and TWA stand for? - ANSWER-TLV: Threshold limit value
TWA: Time weighted average
Is helium lighter or heavier than air? - ANSWER-Lighter
The action of UV light on oxygen produces which toxic gas? - ANSWER-Ozone
Which common fuel gas has the widest range where it can become flammable when
mixed with air? - ANSWER-Acetylene
What substance should you NEVER apply to a stiff pressure-adjusting screw on an
oxygen regulator? - ANSWER-Oil or grease
What is the maximum gauge pressure that acetylene should be used? (kPa/psi) -
ANSWER-103 kPa (15 psi)
Which toxic gas is produced when welding on surfaces with chlorinated hydrocarbon
solvents? - ANSWER-Phosgene gas
What are the 5 basic joints? - ANSWER-1) Butt
2) Corner
3) T
4) Lap
5) Edge
What are the 5 basic weld types? - ANSWER-1) Groove
2) Fillet
3) Plug/Slot
4) Surfacing
5) Edge
, Plasma cutting torch temp can reach temperatures of __________ ° Celsius. -
ANSWER-30,000
True or False: All plasma arc cutting equipment is operated using DCEN. - ANSWER-
True
True or False: Stainless steel can be readily cut with a normal oxy-fuel gas process. -
ANSWER-False
What are the two basic methods of plasma torch operation? - ANSWER-Transferred
and Non-Transferred arc
In North America, the 3 othographic views most commonly-used are: TOP, FRONT and
__________ Side.
[RIGHT / LEFT] - ANSWER-LEFT
What is the difference between a "weld symbol" and a "welding symbol"? - ANSWER-A
"weld symbol" indicates the specific kind of weld to be used (ex. fillet), and is contained
inside of "welding symbol".
In a welding symbol, is the size of the weld located to the LEFT or RIGHT of the fillet
weld symbol? - ANSWER-LEFT
In a welding symbol, is the length of the weld located to the LEFT or RIGHT of the fillet
weld symbol? - ANSWER-RIGHT
In what direction do the electrons flow in an electrical arc?
In arc welding, the arc temperature can exceed temperatures of __________ ° Celsius?
- ANSWER-30,000
Which welding process has the highest arc efficiency? - ANSWER-SAW
Arc voltage __________ when arc length is increased.
[Increased / Decreased] - ANSWER-Increases
In GTAW, what type of penetration and weld width can be expected when using DCEP?
- ANSWER-Shallow penetration, and wide weld
Which polarity is most often chosen for direct current GTAW welding of steels and why?
- ANSWER-DCEN. More heat concentrated at the workpiece --> deeper penetration
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Valedict. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.99. You're not tied to anything after your purchase.
