100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
Previously searched by you
Elevator Mechanic Exam 2024 Latest Update Actual Exam 185 Questions and 100% Verified Correct Answers Guaranteed A+ Verified by Professor$21.49
Add to cart
Elevator Mechanic Exam 2024 Latest Update
2024-2025 Actual Exam 185 Questions and 100%
Verified Correct Answers Guaranteed A+ Verified
by Professor
- CORRECT ANSWER: If you have an elevator that goes 1760 RPM at 60Hz, What Hz
do we need for it to go 600 RPM's
- CORRECT ANSWER: In a series parallel circuit How is resistance totaled?
(1) A parallel connection. (2) A resistive element placed across the terminals of an
armature to bypass a portion of the current. (3) A flexible electrical conductor designed
to conduct current around the mechanical joint between two conductors. (4) The
resistive element (Usually of very low resistance) used in parallel with a DC ammeter
movement to bypass a calibrated portion of the total circuit current. - CORRECT
ANSWER: Shunt Overloads
425 All Pages
(Pi) 3.1416 x (R)radius ²(squared)
Plunger diameter is 10"
So you divide ÷ by 2 = 5
3.1416 x 5² (25)= 78.54 inches - CORRECT ANSWER: Area of a plunger
815 Pg 15
#10 Shade - CORRECT ANSWER: When you are welding with less than 200 Amps.
What shade glass should be in your welding hood?
120 Pg 34
,1 inch is equal to 2.54 cm
1 inch is equal to 25.4 mm - CORRECT ANSWER: Convert Inches to Millimeters
305 Pg Reference Card
1.33 Hz. - CORRECT ANSWER: A newly modernized car has a noticeable vibration,
The application engineer has asked you to determine the frequency (HZ) of your 24"
drive sheave. (Roped 1:1 with a contract speed of 500 Fpm.) What is the frequency?
1/4 Inch wire rope - CORRECT ANSWER: What is an ok substitute for a top rail for a
barricade?
131 Pg 9
1/4" inch - CORRECT ANSWER: You are installing horizontal sliding doors with guides
in each door panel.
How much should the guide engage the sill groove?
525 Pg 23
10 % is desired of each set of wires
15 x 10 ÷ 100 = 1.5 or 2
27 x 10 ÷ 100 = 2.7 or 3
57 x 10 ÷ 100 = 5.7 or 6
Answer: 2 #14, 3 #16, 6 #18 - CORRECT ANSWER: When pulling Hoistway wiring a
10% spare is desirable. If the wiring required (15 - #14 Awg) (27 - #16 Awg) (57 -
#18Awg)
What is the best selection of wires?
,515 Pg 26
10' Ft. - CORRECT ANSWER: OSHA requires that workers have fall protection when
working on scaffolding how many feet above the ground?
137
12 Floors x 3 Elevators= 36 PI's - (3 from 3 floors)9 =27 - CORRECT ANSWER: 12
Floor Building with three cars, 3 floors will not get PI's. How many PI's in total do you
need to order for this job?
15 (Rails) ,16 Lbs., 2 8Ft sections
2 x 8 = 16
total rails are now 16
16 lbs. x 16 ft. (Length of standard rail) = 256 Lbs.
256 Lbs x 16 =4096 - CORRECT ANSWER: Weight of rails
Question: I you have 15 full 16 lbs. rails and two 8' sections. How much do they weigh?
15% 575Fpm
15% is the minimum tripping speed for safties
90 % for electronic trip device
15 x 500 ÷ 100 = 75
75 + 500 = 575 - CORRECT ANSWER: You are testing an elevator with a rated car
speed of 500 fpm. At what minimum speed should the car safeties set.
3 - 225 Ohm resistors in parallel - CORRECT ANSWER: a 75 Ohm resistor has blow
and you don't have a replacement, What can you use?
, 3 Feet - CORRECT ANSWER: You are using a portable ladder to get from landing to
the machine room level. How far above the upper level must the side rails of the ladder
extend?
132 Pg 13
3 Months - CORRECT ANSWER: How often are extension cords checked for
continuity?
129 Pg 20
3 Points of contact shall be maintained..
Note. Ladder should extend 3 feet above upper landing.
1/4 away from height
Step ladders: Never step on top two steps. - CORRECT ANSWER: How many points of
contact should be maintained on a ladder?
132 Pg 13
30° and smaller. It is recommended to use 45° or greater. - CORRECT ANSWER:
Which sling angles are dangerouse
128 Pg 18
36 Inches - CORRECT ANSWER: Two controllers in a small motor room face each
other with the voltages of 500Volts. What is the minimum clearance?
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Tutordiligent. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $21.49. You're not tied to anything after your purchase.
