SOS Mechanic Certification- Suspension & steering Questions and Answers 100- Correct
8 views 0 purchase
Course
Michigan mechanic
Institution
Michigan Mechanic
SOS Mechanic Certification- Suspension & steering Questions and Answers 100- Correct
Bleeding a power steering unit is generally done by
turning the steering wheel left and right repeatedly
After rounding a turn, the front wheels do not return to the straight ahead position in a normal way...
SOS Mechanic Certification- Suspension
& steering Questions and Answers 100%
Correct
Bleeding a power steering unit is generally done by - answer turning the steering wheel
left and right repeatedly
After rounding a turn, the front wheels do not return to the straight-ahead position in a
normal way. What adjustment is most likely to be out of specifications? - answerCaster
"Toe" adjustment on front wheel drive vehicles is made by: - answerchanging he length
of the steering linkage
When performing a front-end alignment what should you do before you adjust the toe
setting? - answeradjust the caster & camber
Front-wheel toe-in adjustment on rear-wheel drive vehicles is made by: -
answerchanging the length of the steering linkage
A mechanic is going to adjust the curb height on a car with torsion bars. To do this the
car should be checked: - answeron a level surface with the car at curb weight
A proper way to check ball joints for wear is by: - answervisual observation of the wear
indicator & unloading the ball joint and using a pry bar and a dial indicator
which of the following adjustments can be made on all vehicles with MacPherson strut
suspensions? - answerToe settings
You are checking the war on ball joints with a dial indicator at the wheel rim. What must
you do to get accurate readings? - answercheck the wheel bearing adjustment and
correct if needed
A mechanic jacks up a car, stands facing it, places a hand on the front of each tire. The
mechanic pushes out and then pulls in on both tires. Too much movement would most
likely mean that: - answerthe tie rod ends are worn
Which of the following should be checked first thing when doing a front-end alignment? -
answerCurb height
, To counteract road crown, most manufacturers recommend that the left front wheel be
adjusted to have: - answerLess positive (+) caster than the right
If the toe-in is too great, the tread will most likely show: - answerfeathered edges on
both front tires
When a wheel alignment is done on a car with front torsion bars, what should be
checked and adjusted first? - answerCurb height
Which of the following would be a typical automobile front end camber setting? -
answer-3 degrees +/- 2 1/4 degrees its not the correct answer
A mechanic finds that a front tire is worn on the inside of the tread only. The mechanic
checks the air pressure and finds it correct. What is causing this problem? - answerThe
camber is set too negative
A car will pull to: - answerthe side with the most positive (+) camber
One front tires shows spotty or isolated cupping and worn spots. What is the most likely
cause of this problem? - answerAn out-of-balance tire.
Before you remove a brake rotor from a hub, you should: - answermark the position of
the rotor
The front wheels shimmy or bounce above 40mpg, even on a smooth, straight road.
The likely cause of this problem is: - answerTires out of balance
While replacing a ball joint, you notice that the tapered hole in the steering knuckle is
oval shaped. What should you do about this? - answerInform the customer that the
knuckle should be replaced.
If the upper ball joints are positioned ahead of the lower ball joints, the condition is: -
answerNegative caster
What is true of most MacPherson type suspensions? - answerThere is no upper control
arm.
A mechanic has set caster, camber, and toe-in to specifications. On the road test
afterwards, the mechanic notices that the steering wheel spokes are off center to the
left. What should be done to fix this? - answerAdjust both tie rod sleeves equally to
move the front wheels in the direction of the steering wheel error
Ball joints with wear indicators should be checked: - answerwhen loaded and by visual
observation
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller julianah420. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $15.49. You're not tied to anything after your purchase.
