Exam (elaborations)
NCTI Installer Technician exam 2023 with 100% correct answers
- Course
- Institution
NCTI Installer Technician exam 2023 with 100% correct answers
[Show more]
Seller
Follow
JUICYGRADES
Reviews received
Content preview
NCTI MT2 - MT3In what applications is a splice closure used? - correct answer -Splice closures are used to protect optical
fibers and splices against a full range of environmental changes in aerial installations or below ground in
vaults.
When preparing a fiber-optic cable for splicing, what is the purpose of removing approximately 2.5 cm (1
inch) of jacket and any armor that is present, from the end of the cable? - correct answer -To access the
cable's rip cord and to check the cutting depth of the knife or ringing tool
what does water do to the glass core of an optical fiber? - correct answer -Water causes the glass core of
the optical fiber to become opaque, which degrades the signal as it's transported through the fiber.
when preparing a splice closure, what should be done with the fiberglass rod strength member that runs
down the center of loose-tube fiber-optic cable? - correct answer -Trim the strength member back for
convenience, but leave it long enough to be tightly clamped to a strain-relief lug in the closure.
What is the purpose of splice trays inside splice closures? - correct answer -Splice trays are designed to
provide protection for mechanical splices, fusion splice protectors, and optical splitters as well as
provide storage for the required fiber slack.
How should the buffer tubes be secured in the closure? - correct answer -The buffer tubes should be
secured with tie wraps to allow slight movement without pulling or stressing the optical fibers.
How are optical splices secured in a splice tray? - correct answer -Retaining clips hold optical splices in
place in a splice tray.
What is the purpose of buffer tubes in fiber-optic cable? - correct answer -Buffer tubes protect and
separate the optical fiber in smaller bundles.
, When splicing fiber-optic cable, why is it a good safety practice to clean off fiber strippers and other
hand tools after each use? - correct answer -To prevent the accidental transfer of fiber debris or fiber
chips onto clean hands.
Where would you expect to install a mid-entry splice in a fiber-optic cable network? - correct answer -A
location where a select number of optical fibers need to be spliced, and the remaining buffer tubes and
fibers remain untouched.
Which type of fusion splicer is ideal for fiber-to-the-x (FTTx) splicing? - correct answer -The fixed V-
groove splicer.
What are some prerequisites before performing a fusion splice of optical fibers? - correct answer -A
controlled environment such as a splicing van, trailer, or tent and a stable work surface that is large
enough to accommodate the fusion splicer, tools, and the splice closure.
When would a mid-entry splice in a fiber-optic network be used? - correct answer -In a self-healing ring
network that requires only two fibers to feed an optical fiber drop.
What is required of mechanical splices used for acceptance testing? - correct answer -A mechanical
splice used for acceptance testing should be simple to use and reusable.
Why are Velcro straps preferred over standard plastic tie wraps when bundling pigtails for storage in a
splice panel? - correct answer -Because Velcro straps are removable and can hold the pigtails together
without placing undue strain on the optical fibers.
When preparing fiber-optic cable for connection to a patch panel, how much buffer tube and fiber slack
should be provided? - correct answer -Leave enough slack in the buffer tubes to allow the splice trays to
reach the splicing equipment and enough fiber slack to store on individual trays for later additions,
moves, and changes.
If tight-buffered distribution fiber-optic cable is installed between the master splice panel in an optical
entrance enclosure (OEE) and a rack-mounted fiber-optic distribution panel, where in the facility must
the distribution panel be located? - correct answer -The distribution panel can be located anywhere in
the facility since the distribution cable complies with indoor code requirements for riser or plenum
installations.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller JUICYGRADES. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $15.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
75632 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now