Package deal
ASE Full Solution Pack Updated 2024,2025 with complete solutions
ASE Full Solution Pack Updated 2024,2025 with complete solutions
[Show more]ASE Full Solution Pack Updated 2024,2025 with complete solutions
[Show more]What would be the most likely result of a missing AC compressor clutch diode? - Answer-Damage to 
the ECM 
Tech A says that the service fittings for R-134a are the same as the service fittings for R-12. Tech B 
says the low-side service fitting is a 16mm quick-connect and high-side is 13mm quick-con...
Preview 1 out of 2 pages
Add to cartWhat would be the most likely result of a missing AC compressor clutch diode? - Answer-Damage to 
the ECM 
Tech A says that the service fittings for R-134a are the same as the service fittings for R-12. Tech B 
says the low-side service fitting is a 16mm quick-connect and high-side is 13mm quick-con...
A diesel engine oil sample shows excessive copper content. Which of the following would be the most 
likely source? 
A. Rod bearings 
B. Exhaust valves 
C. Intake valves 
D. Piston rings - A. Rod bearings 
(Bearings show up in oil samples as copper.) 
A diesel engine suddenly loses oil pressure at i...
Preview 2 out of 13 pages
Add to cartA diesel engine oil sample shows excessive copper content. Which of the following would be the most 
likely source? 
A. Rod bearings 
B. Exhaust valves 
C. Intake valves 
D. Piston rings - A. Rod bearings 
(Bearings show up in oil samples as copper.) 
A diesel engine suddenly loses oil pressure at i...
The right rear brake is dragging on a vehicle with independent rear suspension. All other brakes operate 
normally. Which of the following could be the cause? 
A. Damaged right front brake line 
B. Damaged right rear brake line 
C. Damaged left rear brake line 
D. Damaged left front brake line - B 
...
Preview 2 out of 10 pages
Add to cartThe right rear brake is dragging on a vehicle with independent rear suspension. All other brakes operate 
normally. Which of the following could be the cause? 
A. Damaged right front brake line 
B. Damaged right rear brake line 
C. Damaged left rear brake line 
D. Damaged left front brake line - B 
...
Driveshaft imbalance can sometimes be solved by... - Rotating the shaft and reinstalling. 
Brinelling means? - Bearing raceway has surface indentations. 
Outer ends of axle shafts can be supported by what 3 types of bearings? - Roller, tapered, and ball 
Binding U-Joint will damage?? - Extension hou...
Preview 2 out of 6 pages
Add to cartDriveshaft imbalance can sometimes be solved by... - Rotating the shaft and reinstalling. 
Brinelling means? - Bearing raceway has surface indentations. 
Outer ends of axle shafts can be supported by what 3 types of bearings? - Roller, tapered, and ball 
Binding U-Joint will damage?? - Extension hou...
The tread of a tire is worn in the center and not on the outer shoulders. Technician A says this is caused 
by an improper wheel alignment angle. Technician B says this is caused by over inflating the tire. Who is 
correct? - An over-inflated tire wears the center of the tire's tread. Technician B ...
Preview 1 out of 2 pages
Add to cartThe tread of a tire is worn in the center and not on the outer shoulders. Technician A says this is caused 
by an improper wheel alignment angle. Technician B says this is caused by over inflating the tire. Who is 
correct? - An over-inflated tire wears the center of the tire's tread. Technician B ...
1. The ABS (antilock brake system) and TRACTION OFF indicator lights remain ON with the engine 
running. Technician A says to check for ABS or TCS (traction control system) diagnostic trouble codes. 
Technician B says you can check for ABS or TCS blink codes by connecting two pins of the DLC (Data L...
Preview 2 out of 9 pages
Add to cart1. The ABS (antilock brake system) and TRACTION OFF indicator lights remain ON with the engine 
running. Technician A says to check for ABS or TCS (traction control system) diagnostic trouble codes. 
Technician B says you can check for ABS or TCS blink codes by connecting two pins of the DLC (Data L...
What are the many causes of steering pull due to front tire abnormalities? - Front tires with 
different types, sizes, inflation pressure, tread designs, or a front tire with a conicity defect. 
What is tire conicity? - When a tire bead is not centered on the tire body. The bead forms a cone. 
Whats...
Preview 1 out of 3 pages
Add to cartWhat are the many causes of steering pull due to front tire abnormalities? - Front tires with 
different types, sizes, inflation pressure, tread designs, or a front tire with a conicity defect. 
What is tire conicity? - When a tire bead is not centered on the tire body. The bead forms a cone. 
Whats...
Two technicians are examining a low charge output on a vehicle. Tech A says if the battery is defective it 
can block the output of the alternator. Tech B says that a defective stator could be the cause. Who's 
correct? 
Tech A 
Tech B 
Both 
Neither - Both 
Two technicians are discussing a whining...
Preview 2 out of 5 pages
Add to cartTwo technicians are examining a low charge output on a vehicle. Tech A says if the battery is defective it 
can block the output of the alternator. Tech B says that a defective stator could be the cause. Who's 
correct? 
Tech A 
Tech B 
Both 
Neither - Both 
Two technicians are discussing a whining...
Technician A says that flush mounted/tight fitting molding that are difficult to mask should be removed 
prior to refinishing? Technician B says that parts that can be easily removed should be removed prior to 
refinishing. Who is right? 
A. A only 
B. B only 
C. Both A and B 
D. Neither A nor b - A...
Preview 2 out of 11 pages
Add to cartTechnician A says that flush mounted/tight fitting molding that are difficult to mask should be removed 
prior to refinishing? Technician B says that parts that can be easily removed should be removed prior to 
refinishing. Who is right? 
A. A only 
B. B only 
C. Both A and B 
D. Neither A nor b - A...
It is a good idea to routinely replace cooling system hoses: 
A. after 25,000 miles. 
B. after 50,000 miles. 
C. after 100,000 miles. 
D. based on the OEM schedule. - D is correct 
While performing a scheduled maintenance test drive, which of the following noises would LEAST LIKELY 
be scheduled for...
Preview 1 out of 2 pages
Add to cartIt is a good idea to routinely replace cooling system hoses: 
A. after 25,000 miles. 
B. after 50,000 miles. 
C. after 100,000 miles. 
D. based on the OEM schedule. - D is correct 
While performing a scheduled maintenance test drive, which of the following noises would LEAST LIKELY 
be scheduled for...
If all around braking performance is poor or low air pressure is prevalent what could be the cause? - 
Clogged compressor air filter. Slipping belt. Air leaks. Restricted lines. Defective governor. 
Malfunctioning air compressor. 
If air system pressure is too high what could be the cause? - Defecti...
Preview 2 out of 10 pages
Add to cartIf all around braking performance is poor or low air pressure is prevalent what could be the cause? - 
Clogged compressor air filter. Slipping belt. Air leaks. Restricted lines. Defective governor. 
Malfunctioning air compressor. 
If air system pressure is too high what could be the cause? - Defecti...
The flexible line connected to the front disc brake caliper is cracked. Which of the following should the 
technician do? 
a. repair the section of cracked hose using a barb fitting 
b. replace the hose with a new one 
c. replace all the rubber hoses on the vehicle 
d. replace all the rubber and ste...
Preview 3 out of 17 pages
Add to cartThe flexible line connected to the front disc brake caliper is cracked. Which of the following should the 
technician do? 
a. repair the section of cracked hose using a barb fitting 
b. replace the hose with a new one 
c. replace all the rubber hoses on the vehicle 
d. replace all the rubber and ste...
Who is right? 
A. Technician A only 
B. Technician B only 
C. Both A and B 
D. Neither A or B - D. Total voltage in a series circuit is equal to the sum of the voltages across the 
separate resistances. Total current in a series circuit is the same throughout left sides. 
A vehicle's tum signals fl...
Preview 3 out of 26 pages
Add to cartWho is right? 
A. Technician A only 
B. Technician B only 
C. Both A and B 
D. Neither A or B - D. Total voltage in a series circuit is equal to the sum of the voltages across the 
separate resistances. Total current in a series circuit is the same throughout left sides. 
A vehicle's tum signals fl...
If a vehicle with an air ride suspension won't lower when necessary, what is the most likely cause? - 
The sensor isn't sending the signal that the rear is too hight 
What alignment angle would cause dog-tracking? - Rear toe 
A customer says that their vehicle is difficult to steer, but only in on...
Preview 1 out of 4 pages
Add to cartIf a vehicle with an air ride suspension won't lower when necessary, what is the most likely cause? - 
The sensor isn't sending the signal that the rear is too hight 
What alignment angle would cause dog-tracking? - Rear toe 
A customer says that their vehicle is difficult to steer, but only in on...
Alternator - The electrical device driven by the engine that recharges the battery. It produces 
alternating current using rotating field coils inside stationary stator windings 
Accessories - Parts that add to the appearance or performance of a vehicle 
Accounts Receivable - Money due from customer...
Preview 1 out of 2 pages
Add to cartAlternator - The electrical device driven by the engine that recharges the battery. It produces 
alternating current using rotating field coils inside stationary stator windings 
Accessories - Parts that add to the appearance or performance of a vehicle 
Accounts Receivable - Money due from customer...
A high-pressure injection line is leaking on a pump-line nozzle (PLN) diesel engine. The line has been 
torqued to specification. Which of the following should the technician do first? 
A. Replace the line 
B. Tighten the line 
C. Remove and inspect the line 
D. Replace the line and matching fitting...
Preview 3 out of 17 pages
Add to cartA high-pressure injection line is leaking on a pump-line nozzle (PLN) diesel engine. The line has been 
torqued to specification. Which of the following should the technician do first? 
A. Replace the line 
B. Tighten the line 
C. Remove and inspect the line 
D. Replace the line and matching fitting...
What is a vapor canister? (fuel related) - It contains charcoal granules that absorb fuel vapors and 
is often damaged during collisions. 
Exhaust components consist of... - exhaust pipes, catalytic converters, mufflers, resonators and 
tailpipes. (oxygen sensors are apart of the engine management c...
Preview 2 out of 14 pages
Add to cartWhat is a vapor canister? (fuel related) - It contains charcoal granules that absorb fuel vapors and 
is often damaged during collisions. 
Exhaust components consist of... - exhaust pipes, catalytic converters, mufflers, resonators and 
tailpipes. (oxygen sensors are apart of the engine management c...
The tandem rear axle air suspension ride height rises above normal as the vehicle is unloaded. Which of 
these could be the cause? 
(A) A kinked air spring (bag) supply line 
(B) A leaking height control valve (C) A plugged height control valve exhaust port 
(D) A leaking pressure protection valve -...
Preview 2 out of 9 pages
Add to cartThe tandem rear axle air suspension ride height rises above normal as the vehicle is unloaded. Which of 
these could be the cause? 
(A) A kinked air spring (bag) supply line 
(B) A leaking height control valve (C) A plugged height control valve exhaust port 
(D) A leaking pressure protection valve -...
"Bleeding the brakes" is done for what purpose? - To remove air bubbles for a firm pedal 
"Flushing the brakes" is done for what purpose? - To remove moisture contamination; To remove 
old worn out brake fluid; To restore corrosion protection 
"ATF+4" automatic transmission fluid is used prima...
Preview 2 out of 12 pages
Add to cart"Bleeding the brakes" is done for what purpose? - To remove air bubbles for a firm pedal 
"Flushing the brakes" is done for what purpose? - To remove moisture contamination; To remove 
old worn out brake fluid; To restore corrosion protection 
"ATF+4" automatic transmission fluid is used prima...
A vehicle with a MacPherson strut suspension is damaged in a collision impact to the right front. An 
analysis with a frame/body measuring system shows the top of the strut tower was moved toward the 
vehicle centerline by 14mm. This damage would result in change to which of the following alignment ...
Preview 3 out of 19 pages
Add to cartA vehicle with a MacPherson strut suspension is damaged in a collision impact to the right front. An 
analysis with a frame/body measuring system shows the top of the strut tower was moved toward the 
vehicle centerline by 14mm. This damage would result in change to which of the following alignment ...
There is a loud growling noise only when the vehicle is steered to the right while driving. Which of the 
following could be the cause? 
A. Worn left front brakes 
B. Worn wheel bearing 
C. Worn right front brakes 
D. Sticking brake caliper - B 
The brake system has a soft, sinking pedal with the en...
Preview 2 out of 10 pages
Add to cartThere is a loud growling noise only when the vehicle is steered to the right while driving. Which of the 
following could be the cause? 
A. Worn left front brakes 
B. Worn wheel bearing 
C. Worn right front brakes 
D. Sticking brake caliper - B 
The brake system has a soft, sinking pedal with the en...
a heavy thumping noise occurs with the engine idling, but the oil pressure is normal. this may be caused 
by: 
worn pistons and cylinders, 
loose flywheel bolts, 
worm main bearings, 
loose camshaft bearings, - loose flywheel bolts 
-worn pistons and cylinders would cause a thumping noise during acc...
Preview 4 out of 69 pages
Add to carta heavy thumping noise occurs with the engine idling, but the oil pressure is normal. this may be caused 
by: 
worn pistons and cylinders, 
loose flywheel bolts, 
worm main bearings, 
loose camshaft bearings, - loose flywheel bolts 
-worn pistons and cylinders would cause a thumping noise during acc...
They type of brake fluid recommended for use in the master cylinder is ____________ 
DOT 3 
DOT 4 
DOT 4 + or LV 
Any of the above depending on the vehicle - Any of the above depending on the vehicle 
Why is a scan tool needed when checking the level of automatic transmission fluid? 
To determine th...
Preview 2 out of 15 pages
Add to cartThey type of brake fluid recommended for use in the master cylinder is ____________ 
DOT 3 
DOT 4 
DOT 4 + or LV 
Any of the above depending on the vehicle - Any of the above depending on the vehicle 
Why is a scan tool needed when checking the level of automatic transmission fluid? 
To determine th...
A horn is inoperative. Tech A says in order to repair the horn switch; the Supplemental Restraint System 
should be disabled. Tech B says to check for voltage at the relay. Who is right? - Both techs 
The ball joints on a MacPherson strut suspension are being replaced. Technician A says that the coi...
Preview 2 out of 9 pages
Add to cartA horn is inoperative. Tech A says in order to repair the horn switch; the Supplemental Restraint System 
should be disabled. Tech B says to check for voltage at the relay. Who is right? - Both techs 
The ball joints on a MacPherson strut suspension are being replaced. Technician A says that the coi...
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Stuvia is a marketplace, so you are not buying this document from us, but from seller ACADEMICMATERIALS. Stuvia facilitates payment to the seller.
No, you only buy these notes for $18.99. You're not tied to anything after your purchase.
4.6 stars on Google & Trustpilot (+1000 reviews)
78252 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now