100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
EPA 608 Type 3 questions with correct answers $14.49   Add to cart

Exam (elaborations)

EPA 608 Type 3 questions with correct answers

 293 views  1 purchase

On low pressure chillers, moisture typically enters the refrigerant system through ans air leaks from areas with gaskets or fittings The maximum test pressure for leak testing a low pressure centrifugal is: ans 10 psig Leak test and repair the chiller to reduce refrigerant loss fr...

[Show more]

Preview 3 out of 17  pages

  • May 8, 2023
  • 17
  • 2022/2023
  • Exam (elaborations)
  • Questions & answers
All documents for this subject (44)
avatar-seller
BillRanker
EPA 608 Type 3 questions with correct answers
On low pressure chillers, moisture typically enters the refrigerant system through ans ✓✓ air leaks from areas with gaskets or fittings
The maximum test pressure for leak testing a low pressure centrifugal is: ans ✓✓
10 psig
Leak test and repair the chiller to reduce refrigerant loss from a pruge unit on CFC-
11 chiller ans ✓✓ ...
A hydrostatic tube test kit is used to: ans ✓✓ determine if a tube leaks
Commercial and industrial process refrigeration systems must be repaired when the
leak rate exceeds ____ of the charge per year. ans ✓✓ 35%
Refrigerant recovery typically start with liquid recovery it is faster. ans ✓✓ ...
A rupture disc on a recovery vessel for a low pressure refrigerants relieves at: ans
✓✓ 15 psig
According to ASHRAE Guideline 3-1996, if the pressure in a system rises from 1 mm Hg to a level above ____ during a standing vacuum test, the system should be checked for leaks. ans ✓✓ 2.5 mm Hg
The primary water source for a recovery unit condensing coil is _____. ans ✓✓ local municipal water supply When recharging a refrigeration system with R-11, what vaporpressure is necessary in the shells before changing with liquid? ans ✓✓ 16.9" Hg vacuum
After recovering the liquid refrigerant you must: ans ✓✓ recover the vapor refrigerant
According to the EPA there is approximately _____ refrigerant vapor left in an average 350 ton R-11 chiller at 0 psig pressure once all the R-11 liquid has been removed. ans ✓✓ 100 pounds
Charging refrigerant liquid into a refrigeration system when it is under a 29 inch Hg vacuum can cause the: ans ✓✓ system water to freeze
A system does not have to be evacuated all the way to the required level when: ans ✓✓ leaks in the appliance make evacuation to the prescribed level unattainable
Which of the foloowing repairs would ALWAYS be considered "major" under EPA's ans ✓✓ replacement of evaporator coil
Under EPA's regulation's _______ is used to pressurize a low pressure chiller for the purpose of opening the system for a non major repair? ans ✓✓ warming the
refrigerant
If you are using a recovery machine manufactored AFTER 11-15-93 you must evacuate an low pressure appliance to _______ before making a major repair. ans
✓✓ 25 mm of Hg absolute After reaching the required recovery vacuum on a chiller, you should ans ✓✓ Wait for at least a few minutes to see if the system pressure rises, indicating that there is till refrigerant in a liquid form or in the oil
The pressure corresponding to 32 F for R-123 ans ✓✓ 20 inches of HG vacuum
When evacuating a system the use of too large a vacuum pump can cause? ans ✓✓ trapped water to freeze
Refrigerant-11 at a pressure of 17 inches HG vacuum has a saturation temperature of: ans ✓✓ 35F
During the evacuation of a system containing large amounts of moisture you can prevent freezing of this moisture by increasing the pressure with______gas ans ✓✓ nitrogen
ASHRAE standard 15-1994 requires that each machinery room must activate an alarm and mechanical ventilation beofre refrigerant concentrations exceed: ans ✓✓ the threshold limit valve and time weighted average
The typical design burst pressure for a rupture disk on a low pressure centrifugal air-conditioning system is set at_______ ans ✓✓ 15 psi
Heat pumps that have been retrofitted from R22 to R407C should be leak checked with: ans ✓✓ pressurized nitrogen
When a new system has been assembled, the first thing to do is: ans ✓✓ pressurize the system with inert gas and leak check

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller BillRanker. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $14.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

72349 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$14.49  1x  sold
  • (0)
  Add to cart